㈠ 基於C51單片機的信號發生器
一個數模轉換器就可以了，利用定時器溢出中斷實現，每次溢出中斷對P0口賦值，通常是賦值你編寫好的數組，因為你每次改變io口的狀態，對應DA轉換器輸出電壓的改變，從而產生波形，例如你要產生方波，你初值P0=0xff,進入中斷（設變數A，然後A++）次數達到某個值（例如100）的時候P0取反，然後A清零，每次達到中斷次數100就取反，從而產生方波；三角波，你就每次中斷賦你寫好的數組（從0v~5V單調增的數組）先用數組順序賦值給P0口，達到最後數組的時候，就反過來賦值給P0口，這樣就產生了三角波了。如果要改變頻率的話，你就在中斷加入個變數，這個變數用來給定時器賦重裝值的，通過改變這個變數來改變定時時間，使頻率改變。
㈡ 求一個正確的基於51單片機的函數信號發生器的C程序
#include<reg51.h>
#include<absacc.h>
#include<MAX72191.h>
#defineDAC XBYTE[0x7fff] //P2.7接CS
sbitkey0 = P3^2;// 增減切換鍵
sbitkey1 = P3^3;//個位,十位，百位，千位的控制切換
sbitkey2 = P3^4;// 調整位
sbitkey3 = P3^5;// 波形選擇正弦、三角、矩形波，鋸齒波
unsignedchar i,j;
unsignedint counter,step,flag;
typedefunsigned int uint;
//定時器0初始化
voidInit_Timer0(void)
{
TMOD = (TMOD & 0XF0) | 0X01;//設置工作方式和定時初始值
TH0 = 0xff;
TL0 = 0x00;
TR0 =1; //啟動定時器
ET0 =1;
}
//定義輸出波形的代碼
unsignedchar code type[4][256]={
{ //正弦波代碼
0x00,0x00, 0x00, 0x00, 0x00, 0x00, 0x1, 0x1, 0x2, 0x3, 0x3, 0x4, 0x5, 0x6, 0x7, 0x8,
0x9, 0xb,0xc, 0xd, 0xf, 0x10,0x12,0x13,0x15,0x17,0x19,0x1b,0x1d,0x1f,0x21,0x23,
0x25,0x27,0x2a,0x2c,0x2e,0x31,0x33,0x36,0x39,0x3b,0x3e,0x41,0x43,0x46,0x49,0x4c,
0x4f,0x52,0x55,0x58,0x5b,0x5e,0x61,0x64,0x67,0x6a,0x6d,0x70,0x73,0x76,0x7a,0x7d,
0x80,0x83,0x86,0x89,0x8c,0x8f,0x93,0x96,0x99,0x9c,0x9f,0xa2,0xa5,0xa8,0xab,0xae,
0xb1,0xb4,0xb6,0xb9,0xbc,0xbf,0xc1,0xc4,0xc7,0xc9,0xcc,0xce,0xd1,0xd3,0xd5,0xd8,
0xda,0xdc,0xde,0xe0,0xe2,0xe4,0xe6,0xe8,0xea,0xeb,0xed,0xef,0xf0,0xf1,0xf3,0xf4,
0xf5,0xf6,0xf8,0xf9,0xf9,0xfa,0xfb,0xfc,0xfc,0xfd,0xfd,0xfe,0xfe,0xfe,0xfe,0xfe,
0xfe,0xfe,0xfe,0xfe,0xfe,0xfd,0xfd,0xfc,0xfc,0xfb,0xfa,0xf9,0xf9,0xf8,0xf6,0xf5,
0xf4,0xf3,0xf1,0xf0,0xef,0xed,0xeb,0xea,0xe8,0xe6,0xe4,0xe2,0xe0,0xde,0xdc,0xda,
0xd8,0xd5,0xd3,0xd1,0xce,0xcc,0xc9,0xc7,0xc4,0xc1,0xbf,0xbc,0xb9,0xb6,0xb4,0xb1,
0xae,0xab,0xa8,0xa5,0xa2,0x9f,0x9c,0x99,0x96,0x93,0x8f,0x8c,0x89,0x86,0x83,0x80,
0x7d,0x7a,0x76,0x73,0x70,0x6d,0x6a,0x67,0x64,0x61,0x5e,0x5b,0x58,0x55,0x52,0x4f,
0x4c,0x49,0x46,0x43,0x41,0x3e,0x3b,0x39,0x36,0x33,0x31,0x2e,0x2c,0x2a,0x27,0x25,
0x23,0x21,0x1f,0x1d,0x1b,0x19,0x17,0x15,0x13,0x12,0x10,0xf,0xd, 0xc, 0xb, 0x9,
0x8,0x7, 0x6, 0x5, 0x4, 0x3, 0x3, 0x2, 0x1, 0x1, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00
},
{ //三角波代碼
0x2,0x4, 0x6, 0x8, 0xa, 0xc, 0xe, 0x10,0x12,0x14, 0x16, 0x18, 0x1a,0x1c, 0x1e, 0x20,
0x22,0x24, 0x26, 0x28, 0x2a, 0x2c, 0x2e, 0x30,0x32, 0x34, 0x36, 0x38, 0x3a, 0x3c, 0x3e, 0x40,
0x42,0x44, 0x46, 0x48, 0x4a, 0x4c, 0x4e, 0x50,0x52, 0x54, 0x56, 0x58, 0x5a, 0x5c, 0x5e, 0x60,
0x62,0x64, 0x66, 0x68, 0x6a, 0x6c, 0x6e, 0x70,0x72, 0x74, 0x76, 0x78, 0x7a, 0x7c, 0x7e, 0x80,
0x82,0x84, 0x86, 0x88, 0x8a, 0x8c, 0x8e, 0x90,0x92, 0x94, 0x96, 0x98, 0x9a, 0x9c, 0x9e, 0xa0,
0xa2,0xa4, 0xa6, 0xa8, 0xaa, 0xac, 0xae, 0xb0,0xb2, 0xb4, 0xb6, 0xb8, 0xba, 0xbc,0xbe, 0xc0,
0xc2,0xc4, 0xc6, 0xc8, 0xca, 0xcc, 0xce, 0xd0,0xd2, 0xd4, 0xd6, 0xd8, 0xda, 0xdc,0xde, 0xe0,
0xe2,0xe4, 0xe6, 0xe8, 0xea, 0xec, 0xee, 0xf0,0xf2, 0xf4, 0xf6, 0xf8, 0xfa, 0xfc,0xfe, 0xff,
0xfe,0xfc, 0xfa, 0xf8, 0xf6, 0xf4, 0xf2, 0xf0,0xee, 0xec, 0xea, 0xe8, 0xe6, 0xe4,0xe2, 0xe0,
0xde,0xdc, 0xda, 0xd8, 0xd6, 0xd4, 0xd2, 0xd0,0xce, 0xcc, 0xca, 0xc8, 0xc6, 0xc4,0xc2, 0xc0,
0xbe,0xbc, 0xba, 0xb8, 0xb6, 0xb4, 0xb2, 0xb0,0xae, 0xac, 0xaa, 0xa8, 0xa6, 0xa4,0xa2, 0xa0,
0x9e, 0x9c, 0x9a, 0x98, 0x96, 0x94, 0x92, 0x90,0x8e, 0x8c, 0x8a, 0x88, 0x86, 0x84, 0x82, 0x80,
0x7e, 0x7c, 0x7a, 0x78, 0x76, 0x74, 0x72, 0x70,0x6e, 0x6c, 0x6a, 0x68, 0x66, 0x64, 0x62, 0x60,
0x5e, 0x5c, 0x5a, 0x58, 0x56, 0x54, 0x52, 0x50,0x4e, 0x4c, 0x4a, 0x48, 0x46, 0x44, 0x42, 0x40,
0x3e, 0x3c, 0x3a, 0x38, 0x36, 0x34, 0x32, 0x30,0x2e, 0x2c, 0x2a, 0x28, 0x26, 0x24, 0x22, 0x20,
0x1e, 0x1c, 0x1a, 0x18, 0x16, 0x14, 0x12, 0x10,0xe, 0xc, 0xa, 0x8, 0x6, 0x4, 0x2, 0x00
},
{// 矩形脈沖波代碼
0xff,0xff, 0xff, 0xff, 0xff, 0xff, 0xff, 0xff,0xff, 0xff, 0xff, 0xff, 0xff, 0xff,0xff, 0xff,
0xff,0xff, 0xff, 0xff, 0xff, 0xff, 0xff, 0xff,0xff, 0xff, 0xff, 0xff, 0xff, 0xff,0xff, 0xff,
0xff,0xff, 0xff, 0xff, 0xff, 0xff, 0xff, 0xff,0xff, 0xff, 0xff, 0xff, 0xff, 0xff,0xff, 0xff,
0xff,0xff, 0xff, 0xff, 0xff, 0xff, 0xff, 0xff,0xff, 0xff, 0xff, 0xff, 0xff, 0xff,0xff, 0xff,
0xff,0xff, 0xff, 0xff, 0xff, 0xff, 0xff, 0xff,0xff, 0xff, 0xff, 0xff, 0xff, 0xff,0xff, 0xff,
0xff,0xff, 0xff, 0xff, 0xff, 0xff, 0xff, 0xff,0xff, 0xff, 0xff, 0xff, 0xff, 0xff,0xff, 0xff,
0xff,0xff, 0xff, 0xff, 0xff, 0xff, 0xff, 0xff,0xff, 0xff, 0xff, 0xff, 0xff, 0xff,0xff, 0xff,
0xff,0xff, 0xff, 0xff, 0xff, 0xff, 0xff, 0xff,0xff, 0xff, 0xff, 0xff, 0xff, 0xff,0xff, 0xff,
0x00,0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00,0x00, 0x00, 0x00, 0x00, 0x00, 0x00,0x00, 0x00,
0x00,0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00,0x00, 0x00, 0x00, 0x00, 0x00, 0x00,0x00, 0x00,
0x00,0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00,0x00, 0x00, 0x00, 0x00, 0x00, 0x00,0x00, 0x00,
0x00,0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00,0x00, 0x00, 0x00, 0x00, 0x00, 0x00,0x00, 0x00,
0x00,0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00,0x00, 0x00, 0x00, 0x00, 0x00, 0x00,0x00, 0x00,
0x00,0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00,0x00, 0x00, 0x00, 0x00, 0x00, 0x00,0x00, 0x00,
0x00,0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00,0x00, 0x00, 0x00, 0x00, 0x00, 0x00,0x00, 0x00,
0x00,0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00,0x00, 0x00, 0x00, 0x00, 0x00, 0x00,0x00, 0x00,
},
{//鋸齒波代碼
0x00,0x01, 0x02, 0x03, 0x04, 0x05, 0x06, 0x07,0x08,0x09, 0x0a, 0x0b, 0x0c, 0x0d, 0x0e, 0x0f,
0x10,0x11, 0x12, 0x13, 0x14, 0x15, 0x16, 0x17,0x18,0x19, 0x1a, 0x1b, 0x1c, 0x1d, 0x1e, 0x1f,
0x20,0x21, 0x22, 0x23, 0x24, 0x25, 0x26, 0x27,0x28,0x29, 0x2a, 0x2b, 0x2c, 0x2d, 0x2e, 0x2f,
0x30,0x31, 0x32, 0x33, 0x34, 0x35, 0x36, 0x37,0x38,0x39, 0x3a, 0x3b, 0x3c, 0x3d, 0x3e, 0x3f,
0x40,0x41, 0x42, 0x43, 0x44, 0x45, 0x46, 0x47,0x48,0x49, 0x4a, 0x4b, 0x4c, 0x4d, 0x4e, 0x4f,
0x50,0x51, 0x52, 0x53, 0x54, 0x55, 0x56, 0x57,0x58,0x59, 0x5a, 0x5b, 0x5c, 0x5d, 0x5e, 0x5f,
0x60,0x61, 0x62, 0x63, 0x64, 0x65, 0x66, 0x67,0x68,0x69, 0x6a, 0x6b, 0x6c, 0x6d, 0x6e, 0x6f,
0x70,0x71, 0x72, 0x73, 0x74, 0x75, 0x76, 0x77,0x78,0x79, 0x7a, 0x7b, 0x7c, 0x7d, 0x7e, 0x7f,
0x80,0x81, 0x82, 0x83, 0x84, 0x85, 0x86, 0x87,0x88,0x89, 0x8a, 0x8b, 0x8c, 0x8d, 0x8e, 0x8f,
0x90,0x91, 0x92, 0x93, 0x94, 0x95, 0x96, 0x97,0x98,0x99, 0x9a, 0x9b, 0x9c, 0x9d, 0x9e, 0x9f,
0xa0,0xa1, 0xa2, 0xa3, 0xa4, 0xa5, 0xa6, 0xa7,0xa8,0xa9, 0xaa, 0xab, 0xac, 0xad, 0xae, 0xaf,
0xb0,0xb1, 0xb2, 0xb3, 0xb4, 0xb5, 0xb6, 0xb7,0xb8,0xb9, 0xba, 0xbb, 0xbc, 0xbd, 0xbe, 0xbf,
0xc0,0xc1, 0xc2, 0xc3, 0xc4, 0xc5, 0xc6, 0xc7,0xc8,0xc9, 0xca, 0xcb, 0xcc, 0xcd, 0xce, 0xcf,
0xd0,0xd1, 0xd2, 0xd3, 0xd4, 0xd5, 0xd6, 0xd7,0xd8,0xd9, 0xda, 0xdb, 0xdc, 0xdd, 0xde, 0xdf,
0xe0,0xe1, 0xe2, 0xe3, 0xe4, 0xe5, 0xe6, 0xe7,0xe8,0xe9, 0xea, 0xeb, 0xec, 0xed, 0xee, 0xef,
0xf0,0xf1, 0xf2, 0xf3, 0xf4, 0xf5, 0xf6, 0xf7,0xf8,0xf9, 0xfa, 0xfb, 0xfc, 0xfd, 0xfe, 0xff}
};
//顯示子函數
Disp7219(unsignedlong dat)
{
unsigned char i;
unsigned char led[8];
led[7]=dat%10;
led[6]=dat/10%10;
led[5]=dat/100%10;
led[4]=dat/1000%10;
led[3]=dat/10000%10;
led[2]=dat/100000%10;
led[1]=dat/1000000%10;
led[0]=dat/10000000%10;
for(i=0;i<8;i++)
{
max_7219(i+1, led[i]);
}
}
//延時約1m秒
voiddelay_ms(uint n)
{
uchar j;
while(n--)
for(j=0;j<120;j++);
}
//主函數
main()
{
unsigned int f,n,j;
delay_ms(500);
Init_Max7219();//初始化7219
Disp7219(000);
Init_Timer0();
step=18;
EA = 1;
while(1)
{
if(key0 == 0) n=n+1;
if(n==2)n=0;
if(key1==0) j=j+1;
if(j==4) j=0;
if(n==0 && j == 0 &&key2 == 0) if(step<180) step+=18; //個位增
if(n==1 && j == 0 &&key2 == 0) if(step>18) step-=18; //個位減
if(n==0 && j == 1 &&key2 == 0) if(step<1800) step+=180;//十位增
if(n==1 && j == 1 &&key2 == 0) if(step>180) step-=180; //十位減
if(n==0 && j == 2 &&key2 == 0) if(step<18000) step+=1800;//百位增
if(n==1 && j == 2 &&key2 == 0) if(step>1800) step-=1800;//百位減
if(n==0 && j == 3 &&key2 == 0) if(step<54000) step+=18000;//千位增
if(n==1 && j == 3 &&key2 == 0) if(step>18000) step-=18000;//千位減
if(key3==0)flag=flag+1;if(flag==4)flag=0;
while((!key0)||(!key1)||(!key2)||(!key3));
f=step/18;
Disp7219(f);}//顯示頻率
}
// 定時中斷服務
voidTimer0(void) interrupt 1 using 2
{
TH0 = 0xff;
TL0 = 0x00;
counter = counter + step;
DAC=type[flag][(unsignedint)counter>>8];
}
㈢ 基於51單片機的三角波信號發生器製作需要什麼材料基本的製作流程是怎樣的呢
單片機一片，DA晶元一片，放大電路
單片機接DA晶元，DA晶元接放大電路，如果需要調節電壓幅度，放大電路可以選擇可變增益放大，用單片機控制數字電位器實現。。。
㈣ 51單片機鍵控信號發生器
發現我去年做了一個這樣的，不過我只弄了3種波形，頻率方波的2K這樣，正弦波就比較小了，250HZ以內。按鍵控制波形切換、頻率增減，幅度增減
㈤ 如何用51單片機設計出一個任意波形信號發生器
這個需要DA轉換晶元，將要產生的波形數字化，存入數組中，由單片機按順序依次送往DA晶元進行轉換，例如產生正弦波，頻率50HZ,可以用100個點來描述，每隔200uS送1個數據，100個數據花20ms.數字化點越多，波形越完美，但也與你的DA晶元精度有關，8位DA只能輸入256個數字量，很難得到很好的波形
㈥ 51單片機信號發生器原理
基於單片機的的信號發生器大概有兩種形式，1、全部波形信號由單片機軟體產生，再經由D/A轉換輸出；
2、單片機+專用信號發生系晶元，這種方式單片機僅扮演主控角色，信號由晶元硬體產生；